eth_rem_flowercare-3.2.tar.gz | mtime: 2010-07-13, size: 580219 bytes supported MCUs: atmega168, atmega328p, atmega644 | This tar.gz file contains besides the actual source code also the circuit diagram. Changes since last version: Show absolute time for next timer based watering. Support for atmega644 |
The above software version supports atmega644/atmega644a. There is a difference as to how the capacitive humidity sensor is connected. The above software uses 95% of the space on an atmega168, about 50% of an atmega328p and about 25% of an atmega644. Pinout for atmega644/atmega644a based ethernet boards:
| ||
eth_rem_flowercare-3.1.tar.gz | mtime: 2010-07-01, size: 572945 bytes supported MCUs: atmega168,atmega328p | This tar.gz file contains besides the actual source code also the circuit diagram. Changes since last version: Better interference resistance on manual watering button. Clock system tuned for accuracy. |
eth_rem_flowercare-3.0.tar.gz | mtime: 2010-06-20, size: 572493 bytes supported MCUs: atmega168,atmega328p | This tar.gz file contains besides the actual source code also the circuit diagram. Changes since last version: added automatic timer function |
Version 3.0 introduces a new feature: a timer to water the plants automatically every day. You can set it up to water always at a given time or only if the soil is dry. | ||
eth_rem_flowercare-2.0.tar.gz | mtime: 2010-03-18, size: 127429 bytes supported MCUs: atmega168,atmega328p | This tar.gz file contains besides the actual source code also the circuit diagram. Changes since last version: added a local push button to start/stop watering manually |
Version 2.0 introduces a new feature: a push button connected between GND and pin PB0 can be used to start/stop watering manually. You can configure for how long the water should flow when the push button is pressed. That time is in seconds but it can be a large number (e.g 1800=30min). This allows you to use the system for a pot plant that might just need water for 10sec as well as for a lawn which you want to water for 20min. | ||
eth_rem_flowercare-1.1.tar.gz | mtime: 2010-03-01, size: 112805 bytes supported MCUs: atmega168,atmega328p | This tar.gz file contains besides the actual source code also the circuit diagram. Changes since last version: timeout if there is no sensor attached. |
eth_rem_flowercare-1.0.tar.gz | mtime: 2009-12-30, size: 108446 bytes supported MCUs: atmega168,atmega328p | This tar.gz file contains besides the actual source code also the circuit diagram. Changes since last version: added circuit diagram for fly-back diode, improved makefile |
eth_rem_flowercare-0.9.tar.gz | mtime: 2009-09-19, size: 76993 bytes supported MCUs: atmega168,atmega328p | This tar.gz file contains besides the actual source code also the circuit diagram. Changes since last version: set a minimum graph width |
eth_rem_flowercare-0.8.tar.gz | mtime: 2009-09-08, size: 76604 bytes supported MCUs: atmega168,atmega328p | This tar.gz file contains besides the actual source code also the circuit diagram. Changes since last version: better buf pointer handling, no functional change |
eth_rem_flowercare-0.7.tar.gz | mtime: 2009-09-01, size: 76607 bytes supported MCUs: atmega168,atmega328p | This tar.gz file contains besides the actual source code also the circuit diagram. Changes since last version: fault in pump control code fixed |
eth_rem_flowercare-0.6.tar.gz | mtime: 2009-08-25, size: 76754 bytes supported MCUs: atmega168,atmega328p | This tar.gz file contains besides the actual source code also the circuit diagram. Changes since last version: This is the first public version |
The article: Remote flower watering and monitoring, part II (automatic garden watering) | The corresponding documentation for software version 3.x | |
The article: Remote flower watering and monitoring | The corresponding documentation for software version 1.x and 2.x |